Round T-Bars - 10" Tall- Fully adjustable for fishing multiple rods
- Full horizontal and vertical adjustment
- Stem-lock sprocket locks T-Bar in 12 horizontal positions
Protecting Your Investment
For maximum service from your rod holders and bases we
recommend periodic cleaning of the threads. Spray with WD-40.
FOR SALTWATER APPLICATIONS, ALL MODELS AVAILABLE WITH STAINLESS STEEL STEMS AND NUTS.
Flush Mount T-Bar #T-150- Fully adjustable rod angle
- Fits into flush mount rod holders
- Fully adjustable rod angle
- Designed for trolling or bait fishing
- Adjusts to 2 positions: troll to rear or
drift to side of boat
- Requires two 215B Li'l Pro
or 205B Pro bases
- Bases and rod holders sold separately
- 2 #210-H Rod Holders
- 2 #214-B Bases
- 1 9" Long / Round T-Bar
- 1 10" Stem / #200-B Base and Mounting Screws
- 4 #210-H Rod Holders
- 4 #214-B Bases
- 1 24" Long / 7/8 Dia. Round T-Bar
- 1 10" Locking Stem / #200-B Base and Mounting Screws
Flat Trolling Bars - 10" Tall- Fully adjustable side to side for fishing multiple rods
- Use with any Li'l Pro Series rod holder
#FT-09-H holds 2 rods
#T-118H holds 4 rod holders
#T-009H holds 2 rod holders
Turn Your Boat Into A Fish Catching Machine...
With Driftmaster Trolling Systems
Mounting stems clamp to tube so you can mount to any width boat, up to 8 feet.
1/2" mounting stems fit any Pro Series Base
T-5000-8 Deep Trolling With Down Riggers
If You're Going To Spider Rig,
Do It Right With Driftmaster T-Bars
T-250-H 18" Tall X 24" Wide T-Bar
Patent Pending
Unique Patent Pending Design Utilizes A Super Strong 1 1/2" Diameter Tube For The Vertical Stem.
* Unlimited Rod Adjustment
* Easy To Turn Out Of The Way Of Trolling Motors Or Walk Ways Then Turn Back And Tighten Securely To Get Back To Fishing.
* Can Be Removed And Disassembled For Stroage In About Ten Seconds.
* Polished Stainless Base Mounts Flush And Secures With Four Screws For Strength
* Polished Stem And T-Bar Means Your System Will Look As Good As It Works.
All Driftmaster Round Trolling Bars Allow Unlimited Rod Angle Adjustment By Loosning One Wingnut On The Clamp Base
#FT-18-H holds 4 rods
12" Tall X 1 1/2" Diameter Aluminum Tube
3" Square Stainless Flush Base
Mounts Permanently To Boat
With (4) 1/4" Stainless Screws
T-5100 Troll Master
Patent Pending
Available From 2 - 8 Feet Long, Last Digit Of Part Number Indicates Length (8 Foot Version Shown)
Removes From Boat In Seconds
Use With Round Rail Clamp Bases For Infinite Rod Angle Adjustment
Custome Sizes Available
T-5100-2
3/8" Stainless Rod Runs Through Assembly And Screws Into Flush Base. Tightens On Top With Wing Nut
T-5000-2
1" Diameter X 16 Guage Stainless Tube
Use 215-B Clamp Bases And #210-HLi'l Pro Rod Holders
Or 205-B Calmp Bases And #200-H Pro Rod Holders
T-5000 Troll Pro
Patent Pending
Available From 2 - 8 Feet Long, Last Digit Of Part Number Indicates Length (8 Foot Version Shown)
Vertical Stems Fit Any Pro Base, So You Can Mount It To The Deck, Gunnels, or Existing rails
Use With Round Rail Clamp Bases For Infinite Rod Angle Adjustment
Custom Sizes Available
1" Diameter X 16 Guage Stainless Tube
Use 215-B Clamp Bases And #210-HLi'l Pro Rod Holders
Or 205-B Calmp Bases And #200-H Pro Rod Holders
All Racks Over 4 Feet Long Are Two Pieces Joined By A Bolt On Coupler.
- 4 #210-H Rod Holders
- 1 18" Long / 1 1/2" Wide Flat Bar
- 1 10" Locking Stem / #200-B Base and Mounting Screws
- 2 #210-H Rod Holders
- 1 7" Long / 1 1/2" Wide Flat Bar
- 1 10" Locking Stem / #200-B Base and Mounting Screws
T-250-HC 18" Tall X 24" Wide T-Bar
Patent Pending
#T-250-H Includes (4) #210-H Rod Holders
#T-250-HC Includes (4) #2100-H Gun Slinger Rod Holders
Driftmaster Pro Staffer Kent Driscoll
Driftmaster Pro Staffers Ronnie Capps and Steve Colman
"This 31 lb. Striper hammered the bait hard; the Troll Master didn't even quiver! Great Bar! Great Rod Holders! Thanks Alot!" . . . . . Chris
